ELTAKO TLZ12-8E-230V UC PDF

Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.

Author: Febar Dainris
Country: Saudi Arabia
Language: English (Spanish)
Genre: Photos
Published (Last): 27 October 2014
Pages: 292
PDF File Size: 7.63 Mb
ePub File Size: 13.96 Mb
ISBN: 366-9-35619-146-5
Downloads: 45300
Price: Free* [*Free Regsitration Required]
Uploader: Vunris

Additionally the local advanced automatic reversing system for Venetian blinds at A1 is active: There are four groups of devices1.

Nach der Installation die automatische Tlz12-8ee-230v abwarten, bevor der geschaltete Verbraucher andas Netz gelegt wird. The tl12-8e-230v central command is executed. When the alarm time AZT is reached, the contact switches over from toSET flashes in field 1 and the display of the elapsed alarm period starts in field 2 from 0. Technical data page D8. Up or DOWN is activated by a control signal.

Products and prices 2010

They only switch to dynamic after 1 second continuous operation. If N is connected, the zero passage switching is active. The switching capacity for fluorescent lamps or low voltage halogen lamps with electronic ballast is up to VA.

Also this print-catalogue is only a snap-shot. If the function ESV is set the time ranges twhich can be set with the middle rotary switch are as follows: The dimmer might be destroyed.

Eltako Staircase lighting timer, TLZEV+UC TLZEV+UC | B├╝rklin Elektronik

All other control inputs except eltwko local control with a push-button stay active for local and central control. Output 3 opens with a delay of 5 minutes if the brightness value set is overshot. Two N terminals for secure cross wiring of several counters. Not suitable to feed back the switching voltage signal of a dimmer switch.

  BIOLOGIA SANTILLANA POLIMODAL PDF

All deliveries are subject to an expanded retention of title and are sold according to our price list at the given time. GLE base load elementPTC in a small coupler with connecting leads; can be used directly in a load, a switch box or a junction box. The multi-sensor relay MSR12 evaluates the signals from the multisensor MS once per second, and sends appropriate control signals to the downstream EGS12Z or EGS12Z2 actuators depending on tlz12-8e-2300v setting of the rotary switch on the front.

Zero passage switching with soft start and soft OFF to protect lamps. Zero passage switching to protect contacts and consumers. Accurate timing is self-evident for this electronic device as well as noiseless operation. This is switched off automatically after time variable from 0. In the longitudinal direction the solenoid may be twisted in any direction compared eltakoo the Reed relay. Any assignment of control devices tlz12-8e-23v the switchgear devices can be chosen, and provision is made for easy modi cations,retro tting and eltko, “bit by bit”.

Incandescent lamps and halogen lamps load 1 up to W and fluorescent lamps with conventional ballast units in lead-lag circuit up to VA. Fluorescent lamps with conventional ballast units parallel compensated VA. The current-limiting relay is connected on the load side of the protected relay contact. Continuous power supply V.

The accrued switch-on time is continuously displayed. The corresponding value is indicated in segment 3. The LED below the upper rotary switch on the front indicates a local or central control. It blinks while the relay contact 15 is open 15 closedand tlz112-8e-230v continuously ON as long as the relay contact 15 is closed 15 open.

This results in an additional standby consumption tlz2-8e-230v only 0. In case of a power failure the system is disconnected in a preset sequence. In case of a power failure the switching position and the brightness level are stored. It can therefore be reduced until the loads ylz12-8e-230v barely detectable.

  LINUX ANNOTER FICHIER PDF

If the switch is opened briefly after closing, the light is dimmeduntil the next time it is opened again briefly. Here, the self-learning mains disconnection relays are ideal for such applications. The inrush current is 10mA.

Only 1 watt standby loss. Overload protection and over-temperature switch-off by means of swichting off with automatic tlz1-8e-230v after fault clearance autorecovery function. Technical data page B ELTAKO has developed a well thought-out modular system of control devices and switchgear for mounting in switch cabinets and distribution boards. With manual control and switch position indicator.

Eltako Treppenlicht Zeitschalter Tlz12-8e-230v UC

Affix the two housings in parallel maximum 15mm apart and also screw if necessary. Zero passage switching with soft start and soft OFF to protect lamps. The set parameters are stored in an EEPROM and are eltamo immediately available again when hc power supply is restored after a power failure.

It came into force on 30th October Thus preventing coil power loss even in the on mode. Release and then press and hold down again to change the direction. Control input with internally produced low voltage 24 V DC. Small loads up to 20mA are acceptable and, once major loads are disconnected, they do not prevent field disconnection.

Recommended retail prices excluding VAT. This single-phase energy meter measures active energy by means of the current between input and output and transmits the consumption and meter reading over the Eltako wireless network.