IS 4984 HDPE PIPES PDF

HDPE Pipes: Specifcations. Specification: IS with latest amendments. Material Grade PE All dimension are in mm. OD PN PN 4. PN 6. PN 8. Dinesh Irrigation Private Limited offering Is HDPE Pipes in Jhotwara, Jaipur , Rajasthan. Get contact details, address, map on Indiamart. | ID: We are leading manufacturer of HDPE pipes as per IS The best quality raw materials are procured to offer the pipes meeting the highest quality.

Author: JoJolkree Milkis
Country: Sierra Leone
Language: English (Spanish)
Genre: Software
Published (Last): 7 September 2017
Pages: 34
PDF File Size: 15.51 Mb
ePub File Size: 4.30 Mb
ISBN: 541-7-88538-205-1
Downloads: 3521
Price: Free* [*Free Regsitration Required]
Uploader: Nikosida

K Pandey Alternate Shri C. NOTES 1 The outside diameter shall be measured at a distance of at least mm from the end of the pipe.

Sinha Alternate Shri O. In such cases, the entire circumference of approximately mm long section of pipe shall be divided into pieces measuring approximately mm square.

Sauce Alternate Shri S. Dhage Alternate Shri M. Nominal Diameter DN 1 16 20 25 32 40 50 63 75 90 PN2. The manufacturer or the supplier may be asked to improve the design and resubmit the product for type approval.

In case of variation in water temperature, the working pressure needs to be modified as. Part 1 1 Laying and jointing polyethylene PE pipes’.

The wall thickness shall be measured by a dial vernier or ball ended micrometer. This standard was first published in and revised inand The test pieces shall be kept in the oven at the temperatures and for the periods specified below: Our hdpee product range is well-tested. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by ls to the latest issue of ‘BIS Handbook’ and ‘Standards Monthly Additions’.

  JAIME BATEMAN CAYON PDF

If any of the samples fails in the repeat tests, the typeof pipe shall not be approved. In this fourth revision the following major changes have been affected: Legal Status of Firm Private Ltd.

For the purpose of deciding whether hdppe particular requirement of this standard is complied with, the pippes value, observed or calculated, expressing the hdpee of a test or analysis, shall be rounded off in accordance with IS 2: The lot shall be deemed not to have met these requirements if the number of defectives found in the first sample is greater than or equal to the corresponding rejection numbers given in col 6 of Table 7.

The ends shall be cleanly cut and shall be square with axis of the pipes. Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.

Full text of “IS high density polyethylene pipes for potable water supplies”

The basis for the values specified is: Get best deals for coconut. If in repeat test, no single failure occurs, the type of pipe under hhdpe shall be considered eligible for type approval. The lot shall be considered to have met the requirements of these tests, if none of samples tested fails.

  6ES7 134 4FB01 0AB0 PDF

We offer them in different sizes and diameters and are valued for optimum performance and easy installation.

Slight shallow longitudinal grooves or irregularities iu the wall thickness shall be permis- sible provided that the wall thickness remains within the permissible limits. Find more hxpe in Mumbai Hdpe Tube in Mumbai. Our Company is enjoying technological advantages with latest equipped on-site laboratory at manufacturing plant.

This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. Registered under Indian Companies Act The material of the pipe thus produced shall conform to the requirements of 5.

Bentex HDPE Pipe As Per is 4984, Application:Drinking Water

Phadnis Alternate Shri J, R. Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Page 2, clause 5. The material of the stripes shall be of the same type of resin, as used in the base compound for the pipe.

This Indian Standard has been developed from Doc: Pipes for sewer- age and industrial effluents are being covered in a separate standard.

Sunderamoorthy Shri Thimu G.